Campbell Hausfeld 60 Gallon Air Compressor Manual

The Campbell Hausfeld 60 Gallon Air Compressor is designed for heavy-duty applications, providing reliable performance for both professional and DIY projects. This compressor features a powerful motor, a large tank capacity, and various outlets for air tools. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Operating the Compressor 8. Maintenance 9. Safety Information 10. Troubleshooting

Features at a Glance

Key components: 60-gallon tank, 5.3 CFM at 90 PSI, 1.6 HP motor, dual outlet for multiple tools.

Feature	Description
60-Gallon Tank	Provides extended run time for air tools
5.3 CFM at 90 PSI	Delivers high air flow for efficient operation
1.6 HP Motor	Powerful motor for demanding applications
Dual Outlet	Allows for simultaneous use of multiple tools
Pressure Regulator	Adjustable pressure for different applications
Safety Valve	Prevents over-pressurization
Oil Lubricated	Ensures longevity and smooth operation

Installation

Unpack and inspect contents. Place the compressor on a stable, level surface.

Connect the air hose: Ensure proper fittings are used.
Plug into a grounded outlet: Use a dedicated circuit for optimal performance.
Check oil levels: Ensure oil is filled to the recommended level.
Turn on the compressor: Allow it to build pressure before use.

WARNING! Compressor is heavy; lift with care to avoid injury. Ensure all connections are secure.

First-Time Setup

Power on the compressor; follow the setup instructions.

Check all connections: Ensure hoses and fittings are secure.
Set the pressure regulator: Adjust to desired PSI for your tools.
Test the compressor: Run it briefly to ensure proper operation.

CAUTION! Ensure stable surface; use two people for handling if necessary.

Specifications

Tank Size: 60 gallons.
Motor Power: 1.6 HP.
CFM Rating: 5.3 CFM at 90 PSI.
Maximum Pressure: 135 PSI.
Weight: Approximately 200 lbs.
Dimensions: 48 x 20 x 36 inches.
Power Source: 120V AC, 15A.
Operating Temperature: Standard room temperature.

Controls and Settings

Access controls on the front panel: Power switch, pressure regulator, and outlet connections.

Pressure Regulator: Adjusts the output pressure to match tool requirements.

Safety Features: Includes a safety valve and thermal overload protection.

Connecting Devices

Connect air tools using the appropriate fittings.

Turn off the compressor before connecting tools.
Ensure hoses are free of leaks.
Select the correct outlet for your tool.

Tip: Always check connections before powering on the compressor.

Operating the Compressor

Follow these steps to operate the compressor safely.

Turn on the power switch.
Adjust the pressure regulator to the desired setting.
Connect your air tool and begin operation.
Monitor the pressure gauge during use.

WARNING! Do not exceed the maximum pressure rating.

Maintenance

Regular maintenance is essential for optimal performance.

Check oil levels regularly and replace as needed.
Drain the tank to remove moisture.
Inspect hoses and fittings for wear and tear.

CAUTION! Always unplug the compressor before performing maintenance.

Safety Information

Read all safety instructions before operating the compressor.

Always wear safety goggles when using air tools.
Keep the compressor in a well-ventilated area.
Do not operate in wet conditions.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Compressor won't start	Power supply issue	Check power cord and outlet.
Low pressure	Leak in hose	Inspect and replace damaged hoses.
Excessive noise	Loose parts	Tighten all screws and fittings.
Compressor shuts off	Overheating	Allow to cool down; check for blockages.

Reset: Follow the manufacturer's instructions for resetting the compressor.

Service: Contact customer support for further assistance.